High quality Tenergy RCR 123 rechargeable kit featuring a microprocessor controlled charger, car cigarette socket adaptor lead and four 3 volt electronically protected Tenergy RCR 123 rechargeable batteries. Suitable for LED flashlights, cameras etc. Suitable for Fenix P1D, P2D, PD20, P3D, PD30 and TK10.
Runtimes,
P1D Q5 Max = 20 mins - Primary = 60 mins per battery
P3D Q5 Turbo = 45 mins - High = 125 mins per pair
Charger features
- Smart microprocessor cut off at full charge
- Thermal, overcharge, short circuit and reverse polarity protection
- Worldwide voltage mains adaptor with supplied UK plug adaptor +12V car adaptor
- Charge 1 - 2 RCR 123 in 1.5 - 2 hours
Battery features
- 3 volt working voltage with manufacturer rated 900 mah capacity.
- Can be re-charged up to 1000 times
- Replaces CR 123A primary battery for digital cameras and LED flashlights
- Internal voltage regulator switches from 3.6 to 3V within 12 ms
- Full PCB electronic protection against over charge, over discharge, over current and short circuit, along with voltage regulation
- 16.5 mm dia x 34 length
Not suitable for 6 volt incandescent torches as the 12 milliseconds it takes for the voltage regulators to kick in is enough to fry the bulb !
Caution
Use only the included charger to charge these batteries. Do not charge these batteries in any other charger. Don't mix rechargeable and non rechargeable cells in the same equipment. Don't mix partly discharged and fully charged batteries. Lithium batteries can explode if mis treated so please take note of the above warning.
IN STOCK Free first class post
.JPG)
Tenergy 3 volt rechargeable lithium CR 123 batteries. Suitable for all Fenix CR 123 powered models and many other makes. Rechargeable only with our Tenergy branded 3 volt charger according to our supplier. Other chargers NOT recommended.
Battery features
- 3 volt working voltage with manufacturer rated 900 mah capacity.
- Can be re-charged up to 1000 times
- Replaces CR 123A primary battery for digital cameras and LED flashlights
- Internal voltage regulator switches from 3.6 to 3V within 12 ms
- Full PCB electronic protection against over charge, over discharge, over current and short circuit, along with voltage regulation
- 16.5 mm dia x 34 length
Not suitable for 6 volt incandescent torches as the 12 milliseconds it takes for the voltage regulators to kick in is enough to fry the bulb !
Caution
Use only the intended charger to charge these batteries. Do not charge these batteries in any other charger. Don't mix rechargeable and non rechargeable cells in the same equipment. Don't mix partly discharged and fully charged batteries. Lithium batteries can explode if mis treated so please take note of the above warning.
IN STOCK Priced per pair Free first class post
The Ultrafire WF 138 charger is recommended for charging both the AW RCR 123 rechargeable cells and Ultrafire 16340 RCR 123 rechargeable cells that we sell.
Features
Caution ! Please use Lithium batteries and chargers with caution ! Always charge the cells in a fire proof container and never leave them unattended whilst being charged or used. Problems are rare, especially with protected cells - chargers but we advise caution. Protect the cells from hard impact and crushing as this can also set off a chemical reaction with lithium chemistry.
IN STOCK Free first class post
.JPG)
Make your high performance Fenix TK10 or P3D rechargeable with this excellent kit that includes two High Cap AW RCR 123A batteries and a two bay intelligent charger.
Charge kit features
- AW branded highest quality cells
- High capacity - 750 mah 3.7 volt cells
- High current rated
- Anti explosion vent module for added safety
- PCB built into each cell providing over charge protection - over discharge protection - short circuit and over current protection.
- Max recommended discharge rate 1.5Amps
- Charger features two independent charging channels allowing you to charge one or two batteries at a time
- Indicator LED on each channel - red = charging - green = charged
- Automatic overcharge protection cuts power when batteries are fully charged
- 3 Volt and 3.7 volt settings to charge either rechargeable battery type
- Recharge time approximately 3 hours
- Mains lead fitted with UK plug
Note - batteries not suitable for use with our Tenergy Charger ! This charger not suitable for Tenergy RCR 123 batteries
We've runtime tested these in our shop TK10 at the high output setting. The result - an impressive 54 minutes before the battery protection shut down the cells - brilliant ! We've not tested runtime on the low setting but expect around 5 - 6 hours per charge. Also suitable for the Fenix P3D Q5. These cells can be used in the Fenix P1D and P2D but because of the extra voltage only the max output level will work throughout most of the batteries charge.
Caution ! Please use Lithium batteries and chargers with caution ! Always charge the cells in a fire proof container and never leave them unattended whilst being charged or used. Problems are rare, especially with protected cells - chargers but we advise caution. Protect the cells from hard impact and crushing as this can also set off a chemical reaction with lithium chemistry.
IN STOCK Free first class post.
.JPG)
AW RCR 123 battery specs
These cells feature excellent quality and they deliver their full rated capacity. Highly recommended for the Fenix TK10 and P3D models and many other LED flashlights that can handle 3.7 volt cells. Can be used in the Fenix P1/ /2D but the lower brightness modes won't operate until the battery drops below 3 volts.
Recommended charger for these is the Ultrafire WF 138. Wf 139 can also be used with suitable spacers or dummy cells.
IN STOCK Priced per pair. Free first class post.
.JPG)
A good quality budget RCR 123 rechargeable battery that features a built in protection PCB and 3.6 v working voltage. Manufacturer rated capacity is 880 mah.
This cell doesn't fit Fenix torches but can be used in many others. Please measure your application before ordering.
Dimensions of the battery are Length 36mm - Diameter 16mm.
Rechargeable in the Ultrafire WF 138 charger (tight fit) or in the Ultrafire 139 charger with suitable spacers or dummy cells. These are 3.7 volt cells with full electronic protection . We charge these cells fully before shipping.
IN STOCK Priced per pair Free first class post.
The Ultrafire WF 139 dual bay charger is a versatile piece of kit capable of charging several different 3.6 / 3.7 volt lithium battery types thanks to its spring loaded contacts that allow for various length batteries.
- Charges 14500 - 17500 - 17670 - 18500 - 18650 batteries. Will also charge RCR 123 cells with suitable spacers.
- Two independent charging channels able to charge two different battery types at the same time.
- Auto cut off at full charge
- LED indicators for charging / fully charged condition
- Supplied with UK plug adaptor
- Tested by TPS before shipping
PCB Protected batteries recommended for use with this charger.
Spacers and battery are for illustration only and are not included. Please select "with spacers" from the options below to purchase your charger ready to charge 3.7 VOLT RCR123 batteries.
IN STOCK Free first class post.
.JPG)
Add to the versatility of your Ultrafire WF 139 charger with this pair of AW's machined aluminium battery spacers that enable charging of 3.7 volt RCR 123 batteries such as AW's 750mah.
Not suitable for 3 volt Tenergies.
IN STOCK Priced per pair Free first class post.
